A wide range of Internet of Things (IoT) services are being embraced in
cities. Deep indoor connectivity is a requirement for many of these
services. This edition of the Ericsson Mobility Report uses a simulation
of a realistic large-scale IoT service scenario in a city to show that
up to 99 percent of devices located deep indoors could be reached with
new cellular technologies for the IoT.
Cellular networks are well-suited to
providing connectivity for emerging IoT applications due to their
ubiquitous deployments, as well as their inherent characteristics, which
include security and reliability. Currently, the main role of cellular
networks is to provide mobile broadband coverage. Connectivity for IoT
devices poses new coverage challenges for a variety of use cases. The
newly standardized 3GPP Low-Power Wide-Area (LPWA) cellular
technologies, Cat-M1 and NB-IoT, can be deployed on existing LTE
networks, and are helping to overcome these challenges. The technologies
meet massive IoT coverage requirements and support a wide range of
low-cost devices.
Cat-M1 is a solution designed to support a wide range of IoT
applications, from simple to rich content. This includes such
applications as connected waste bins through to alarms incorporating
emergency voice assistance and fleet management. Cat-M1 provides
theoretical peak uplink data throughput of around 1 Mbps. However, there
is a compromise between the data throughput and coverage: the lower
bitrate the application requires, the further the coverage is extended
for the application. The minimum connectivity target has been set to a
maximum coupling loss (MCL)1 of 160 dB where the achievable uplink data rate is around 1 kbps.2 This can be compared to an MCL of 144 dB for broadband LTE with up to 1 Mbps in downlink and a few 10s of kbps in uplink.
NB-IoT is a narrowband solution, which is designed to provide even better coverage and enables deployment of devices with an even lower cost than Cat-M1. It targets ultra-low-throughput IoT applications, such as smoke detectors and utility meters. The minimum connectivity target has been set to an MCL of 164 dB where the achievable uplink data rate is around 300–400 bps.3 Both technologies support the massive IoT use cases exemplified in the figure.
IoT devices, with a density of around 20,000 per square kilometer, were uniformly distributed across the city, both outdoors and indoors, and corresponding signal strength attributed to the different environments. For example, basements located partly underground were modelled with an additional path loss6 of 5 dB in addition to the signal attenuation indoors (10–30 dB), and those fully underground (deep indoors) with 20 dB.
The coverage was simulated for an IoT application on broadband LTE, Cat-M1 and NB-IoT. The same cell layout was used to calculate coverage for each technology. Network coverage was analyzed in two frequency bands: one lower band (800 MHz) that has the advantage of stronger signal propagation for further coverage, and one higher band (2.6 GHz) offering greater capacity. The table above shows the percentage of devices reached for each technology.
Coverage is enhanced for low-data-rate IoT devices by reducing the data rate to provide additional coverage. With 3GPP targets already exceeded in evaluations, the enhancements will enable massive IoT city deployments with up to 99 percent coverage of devices using cellular networks for connectivity.
Supporting diverse use cases
NB-IoT is a narrowband solution, which is designed to provide even better coverage and enables deployment of devices with an even lower cost than Cat-M1. It targets ultra-low-throughput IoT applications, such as smoke detectors and utility meters. The minimum connectivity target has been set to an MCL of 164 dB where the achievable uplink data rate is around 300–400 bps.3 Both technologies support the massive IoT use cases exemplified in the figure.
Massive IoT city model
Network coverage for massive IoT applications in a metropolitan area was analyzed. Measurements from a commercially deployed LTE network5 for broadband services were used to calibrate a model for simulating broadband LTE, Cat-M1 and NB-IoT coverage. A three-dimensional model of a city was used, with close to 1,000 buildings per square kilometer with an average of 5 floors per building. Both line-of-sight and non-line-of-sight characteristics, including outdoor-to-indoor and indoor radio propagation models, were considered. Typical radio base station site characteristics were assumed, with inter-site distances of approximately 500 meters.IoT devices, with a density of around 20,000 per square kilometer, were uniformly distributed across the city, both outdoors and indoors, and corresponding signal strength attributed to the different environments. For example, basements located partly underground were modelled with an additional path loss6 of 5 dB in addition to the signal attenuation indoors (10–30 dB), and those fully underground (deep indoors) with 20 dB.
The coverage was simulated for an IoT application on broadband LTE, Cat-M1 and NB-IoT. The same cell layout was used to calculate coverage for each technology. Network coverage was analyzed in two frequency bands: one lower band (800 MHz) that has the advantage of stronger signal propagation for further coverage, and one higher band (2.6 GHz) offering greater capacity. The table above shows the percentage of devices reached for each technology.
Extending the LTE coverage for IoT
The 800 MHz band modelling showed that in challenging radio signal propagation environments, such as deep indoors, both Cat-M1 and NB-IoT can reach up to 99 percent of the devices. This can be compared to broadband LTE that would reach 77 percent of mobile broadband devices. In the 2.6 GHz capacity band, the coverage of both Cat-M1 and NB-IoT is also substantially better than the broadband LTE coverage of only 32 percent.Coverage is enhanced for low-data-rate IoT devices by reducing the data rate to provide additional coverage. With 3GPP targets already exceeded in evaluations, the enhancements will enable massive IoT city deployments with up to 99 percent coverage of devices using cellular networks for connectivity.
No comments:
Post a Comment